Role Responsibilities: • Mechanical and reinstatement works including alignment (Rotating alignment tool) of HP and Booster pumps and motors at 3GI TTF. • Inspection and verification of pipelines, equipment, pumps, plate heat exchangers, chillers and boilers for commissioning and start-up activities. • Involvement in the process of commissioning activities during SAT (Site Acceptance Test) test period. • Control and monitoring of ongoing jobs withing pipeline team and contractors. • Reporting and interaction with TCO and third parties. • Supervision of personnel in the scope of daily activities. • Carry out hydrotest and ILI (Inline Inspection) pigging on HPTP pipelines going from 3GI to DPs. • Thermal testing shall be carried out for all 3GI sour gas injection pipeline to validate the current injection pipeline design. • We tested pipeline with Rosen company for pigging works and all preparation work for thermal testing scope. We also tested with nitrogen gas all temporary pipelines (Leak Test) • Participation in introduction and acknowledgement of IIF Culture and HES Standards.

• Oversees the BP’s construction activities from installation to handover of Civil, Structural & Architectural systems related to earthworks, stick-build, modules, buildings, and equipment within the MEI Blue areas of 3GP. • Responsible for supervising construction work and other duties as assigned/directed by the Area Construction Manager. • Supervises and coordinates the work activities with the ME&I BP, subcontractors, and vendor service reps, along with supporting resources and activities. Communicates with the PMT and BP craft supervisors on issues related to interfaces, sequence of work and SIMOPS. • Monitors construction activities to ensure adherence to safety and quality standards to achieve work efficiency and clean MC. • Plays an active role in the development of the safety and IIF culture on the project, making safety an integral part of all work performed. • Remains knowledgeable of safety policies and procedures as well as performs assigned duties in a safe manner and, while supervising others, has responsibility for their safety and ensures that they comply with established safety policies and procedures and practice safe work habits. • Ensure the Contractor performs work in conformance with plans, specifications, schedules, cost control estimates and 120 Day schedule and 4 Week look ahead. • Monitors 4WLH Scheduled activities and ensures equipment, material and manpower requirements are met to support the established completion dates. • Coordinates craft personnel, material, and equipment needed to meet schedules including SIMOPS operations. • Reviews work assignments with craft supervisors and gives instruction relative to the methods and procedures that support work being performed. • Participates in the close-out of construction complete IWP’s and QVD’s

Responsibilities: • Supervision of all piping works and ensure and quality standards of the client. • Coordinate piping fabrications activities for shut down activities. • Coordinate piping spools pressure tests. • On welding and assembly works on the subject of quality and compliance of their quality procedures (WPS) and technical drawings and regulatory documents (GOST,ANSI, API, ASME) • Submit the work permit in a daily safety meeting. • Coordinate piping installation according to the refurbishment schedule. • Check the piping NDT status as per needs. • Check the piping painting and insulation status as per schedule. • Hand over the piping systems to the client • Prerequisites/Requirements.

Responsibilities: • Knowledge of security policies, statements, and procedures, as well as performing established security responsibilities and, at the same time, monitoring other professionals on the site responsible for their security and ensuring that they comply with established security policies and procedures and safe work practices • Responsible to the Superintendent in the overseeing the following functions from installation to handover of Field Installed Mechanical equipment, • Module Hook up, Carry over work, Structural Steel and other duties as assigned/directed by the Superintendent. • Provide Field oversight and coordination of the field work activities with the Mechanical contractor and all ME & I construction-related interface and support activities • Monitors construction activities to ensure adherence to safety and quality standards and to achieve work efficiency • Ensure the Contractor performs work in conformance with plans, schedules, and cost control estimates • Monitors Scheduled work activities and manpower requirements are met to the established completion dates • Familiarity with 4 week look ahead planning and becomes aware of the implementation of Construction Work Pack processes (CWP, IWP) • Coordinates craft personnel, material, and equipment needed to meet schedules while adhering to budget constraints • Reviews work assignments with craft supervisors and gives instruction relative to the methods and procedures that can be used • Ability to interpret drawings, specifications, material requirements, Quality, Lifting & rigging drawings along with Method Statements applicable to Construction projects • Coordination with Scaffolding, Coatings, Insulation, and HVAC disciplines throughout multiple areas, also welding works.

Repair of stationary equipment during Turnaround disclosure and stunning of the pump, filter and reactor. Bolt torque and tensioning of bolted flanges on multiple gauge plant pipe. Torque & tension joints designated on isometric drawings using manual and hydraulic equipment and specified torque/tension figures. Hot torque. Reading piping isometric drawing, piping and instrumental diagram (Iso, P&ID) Experience on Job Hazard Analysis. Knowledge of Permit system. Worked on TCO standard (ANSI, ASME, GOST, API)Able to work on tightening pumping equipment HYTORK and ULTRASONIX, Bigbar NORBAR and hydraulic XLCT, MXT, LDF and STEALTH

Shutdown at platform ‘LUN-A’ for Sakhalin Energy Shutdown at platform ‘PA-B’ for Sakhalin Energy Bolting and machining operator. Bolt torque and tensioning of bolted flanges on multiple gauge plant pipe. Torque & tension joints designated on isometric drawings using manual and hydraulic equipment and specified torque/tension figures. Hot torque. Reading piping isometric drawing, piping and instrumental diagram (Iso, P&ID) Experience on Job Hazard Analysis. Knowledge of Permit system. Able to work on tightening pumping equipment HYTORK and ULTRASONIX, Bigbar NORBAR and hydraulic XLCT, MXT, LDF and STEALTH

• Supervision of all piping works and ensure and quality standards of the client. • Coordinate piping fabrications activities for shut down activities • Coordinate piping spools pressure tests; • On welding and assembly works on the subject of quality and compliance of their quality procedures (WPS) and technical drawings and regulatory documents (GOST,ANSI, API, ASME) • Submit the work permit in a daily safety meeting; • Coordinate piping installation according to the refurbishment schedule; • Check the piping NDT status as per needs; • Check the piping painting and insulation status as per schedule; • Hand over the piping systems to the client • Prerequisites/Requirements. Obtain permit to work. The staff is familiar with the order of #388 "Special precautions for systems that could contain H²S (Relief system, Oil and Gas Lines, Amine System, Sour water, liquid sulphur lines, ert) and must follow the requirements of the order. Prepare the work area, ensure facility is clean and free access to the work area is restricted as per SI-127. Flow Line Depressurised 0 Bar to MRM. Remote Well and Host Well Sweetened w/STC and Shut In. o Flow Line Sweetened w/STC w/Volume Sufficient to Displace the length of flow Line from Choke to pig Launcher. Verify pig Launcher and pig receiver valves are leak-tight by checking pig trap pressure gauge readings. Check position of the HPFG spectacle blind at the bypass valve upstream of the pig receiver, The spectacle blind must be in opened position. Request for a vacuum truck to be onsite.

• To ensure the isometric drawing received from the client and to identify the pipelines and carry out the inspection work. • Check from direction arrows on valves; verify that they are properly identified and valves are installed in accordance with flow direction. • Ensure that pipe supports, hangers and guides have been installed in accordance with the piping drawings and the pipe support details. • On welding and assembly works on the subject of quality and compliance of their quality procedures (WPS) and technical drawings and regulatory documents (GOST,ANSI, API, ASME) • Supervise and Inspection of cold and hot insulation, cladding on piping and equipment. • Line check to verify the use of correct material fittings, valves and supports prior to hydro test and prepare punch list for incomplete works, check and closing after the work is done. • All work well, group metering stations (Group Metering) • Prerequisites/Requirements. Obtain permit to work. The staff is familiar with the order of #388 "Special precautions for systems that could contain H²S (Relief system, Oil and Gas Lines, Amine System, Sour water, liquid sulphur lines, ert) and must follow the requirements of the order. Prepare the work area, ensure facility is clean and free access to the work area is restricted as per SI-127. Flow Line Depressurised 0 Bar to MRM. Remote Well and Host Well Sweetened w/STC and Shut In. o Flow Line Sweetened w/STC w/Volume Sufficient to Displace the length of flow Line from Choke to pig Launcher. Verify pig Launcher and pig receiver valves are leak-tight by checking pig trap pressure gauge readings. Check position of the HPFG spectacle blind at the bypass valve upstream of the pig receiver, The spectacle blind must be in opened position. Request for a vacuum truck to be onsite. • Prepare "Hydrotest" removal and installation of valves Leak test, strength Design pressure Design temperature Test pressures for each target Calibration of the test equipment within 24 hours before the test, end time, test Construction and installation works Draining liquid from line Dismantling test equipment Bolt tightening The installation-test equipment Work with schematic drawings showing the location of instrumentation, plugs, plugs, filling points and connection of measuring circuits. Work with control and measuring equipment

• Management of all activities related to the pipeline (including support) making TLM modile with a contractor from detailed design to commissioning. • Supervise the activates of all pipelines for TLM, including commissioning (if required), punch list and progress measurement (procedure and verification). • On welding and assembly works on the subject of quality and compliance of their quality procedures (WPS) and technical drawings and regulatory documents (GOST,ANSI, API, ASME) • Liaise with QC inspector inspection for any questions. • Ensure that the manufacturer complies with the requirements of the contract and project documentation. • Ensure that documentation is properly filled and available • Review and comment on the schedule production pipelines • Work on wells and group measuring units (Group Metering) • Prerequisites/Requirements. Obtain permit to work. The staff is familiar with the order of #388 "Special precautions for systems that could contain H²S (Relief system, Oil and Gas Lines, Amine System, Sour water, liquid sulphur lines, ert) and must follow the requirements of the order. Prepare the work area, ensure facility is clean and free access to the work area is restricted as per SI-127. Flow Line Depressurised 0 Bar to MRM. Remote Well and Host Well Sweetened w/STC and Shut In. o Flow Line Sweetened w/STC w/Volume Sufficient to Displace the length of flow Line from Choke to pig Launcher. Verify pig Launcher and pig receiver valves are leak-tight by checking pig trap pressure gauge readings. Check position of the HPFG spectacle blind at the bypass valve upstream of the pig receiver, The spectacle blind must be in opened position. Request for a vacuum truck to be onsite. • Prepare "Hydrotest" removal and installation of valves Leak test, strength Design pressure Design temperature Test pressures for each target Calibration of the test equipment within 24 hours before the test, end time, test Construction and installation works Draining liquid from line Dismantling test equipment Bolt tightening The installation-test equipment Work with schematic drawings showing the location of instrumentation, plugs, plugs, filling points and connection of measuring circuits. Work with control and measuring equipment