- Vendor shop inspection visits with daily basis - Long term/Short term project inspections at Vendor shop/ Plant/Site - Preparing daily/weekly inspection reports - Preparing Inspection release notes - Preparing Punch List or NCR if nesessary - Paricipated in Turnaround (Shutdown) 2023 at KTL Plant manifold-2 Gas/Oil & Sulphur. (Tengiz field/TCO) - Mechanical Inspection of ESD Valves with electro-hydraulic actuator; 100% On/Off operation, 100% ESD Time off and Opening/Closing - Performing FAT ,Hydrostatic High Pressure Shell Test, Seat Test, Backseat Test, Pneumatic Low Pressure Test for different types of Valves - Visual & Dimensional inspection - Painting Inspection (DFT) - Preservation & Packing Inspection

KSU project / Substation - Visual inspection of Steel Structure - Reviewing of NDT Reports & Weld Map

Mechanical - Visual inspection - Installation of equipment - Flange management. - Bolt torquing/ tensioning. - Inspection and Test Plan/Checklists (ITP/CL) Piping - Flushing of pipework. - Chemical cleaning and testing of pipework. - Drying, Preservation, Reinstatement - Hydrotest, Pneumatic Test - Pneumatic and hydraulic tubing. - HVAC pipework, weld standards and pressurized heating systems - Installation of various type of valves, including easy drives, gear boxes. Welding - Inspection before, during and after welding process - Witnessing of WPS, NDE and PWHT - Root cause analysis - Raising Punch List, SR, NCR - Review ITP, SQM, Test Pack, Job Pack

To plane, develop, coordinate and direct mechanical completion, pre-commissioning activities of the Top side cluster EPC-4 Module for Kashagan Field Development Experimental Program. To assist with identification of hand over systems and establishment of priorities and sequence of mechanical completion. To review during the construction phase, the status of constructing and punch listing to ensure system are turned over to pre-commissioning in a smooth, safe and efficient manner. Coordinating with the vendor, client representative to obtain approval for work as it is accomplished. Mechanical - Visual inspection for complete and correct installation. - Flange management. - Alignment. - Load testing of lifting equipment. - Hot oil flushing. - Bolt torquing/ tensioning. - Inspection and Test Records/Checklists (ITR/CL) - Dimension control. - Preservation. Piping - Removal of all items subject to damage during flushing, cleaning and pressure testing. - Flushing of pipework. - Chemical cleaning and testing of pipework. - Control of the assembly of pipe studs, preparation of technical documentation, test packages for the hydraulic, pneumatic testing process of testing the strength and visual, leak test. - Drying of tested pipework. - Preservation of tested pipework. - Reinstatement of all items after testing. - Final inspection of pipework. - Test ISO's and P&ID's showing the extent of each pressure test. - Pneumatic and hydraulic tubing. - Hot oil flushing of pipework. - Witnessing of hydrostatic test (up to the 1440 bar), leak test and service tests. - Pipe supports completed.

- To check the progress of the work performed by the contractor, responsible for the time sheets for the work force - To participate in technical reviews - HVAC & Pipe work Work with different types of valves PSV, Gate valves, Ball valves and others. Testing and calibration of valves.Testing under high pressure, hydro test, air test, leakage test Repair, installation, testing of valves and pumps

Worked with equipment of different supplier, follow with them (manufacture) recommendation. - Prepare all necessary documentation: acts, check lists, NCR etc. - carries out tests or jobs assigned by the discipline leader - Follow safety regulations and applies them in practice - Internal inspections of Vessels (cylinders, columns, filters), LPG Tanks - Took part in final close up of vessels, tanks, columns and filters Run tests of pumps, greasing motor and fan bearings Couple assembling and disassembling Mounting of motors and pumps Calibration and inspection of valves, mechanical isolation of valves with P&ID drawings - supervises units operation under critical and emergency situations decision making - provides technical assessment and support for commissioning Mechanical/Electrical/I&C issues regarding site queries submitted by Contractors - Complete Check Lists(A-B)/Punch Lists jointly with MC group. -Visual examination of welded joints Monitoring compliance with welding technology, according to the procedures. Checking the certificates of materials used for welding (additives, electrodes, fittings). Verifying compliance with the welding technology. - Responsible for the following construction of Quality Control by mechanical parts -A visual examination of welded joints in accordance with the project, the terms of ASME, API, SNIP Letting the customer documentation ,coordination inspectors track welded joints on the passage NDT & PWHT, UT,RT,MT,PT,HT. Working with drawings Knowledge of safety norms and instruction key Experienced in the field of Mechanical Inspection and Quality Control involved in fabrication, erection and installation works of refinery, industrial, petro-chemical plant, pipeline and other related projects.. Participated projects as: CGTP-3 (Complex Gas Treatment Plant) Zhaikmunai Byelkamit/AtyrauNefteMash Vessels V-3900, V-3920 Project Gateway ventures TA-2015, TA-2016 Project Hyosung T-1500 amine tank / South korea Project High pressure valves PSV/FlowUAE Project

Survey and checking the assembling of equipment and piping (pre commissioning) as per Project Specification and RoK Law and standards. - Preparation for testing and testing of the following equipment: motors, pumps, compressors, valve actuators (electric, pneumatic, hydraulic drive). Hydro test of vessel and tanks. - Comissioning works of high pressure pumps‘’Goma Pump’’ on the Heidelbergcement plant at Shetpe/ Mangystau region. Before was trained at the Goma Pump Manufacture in India - Performing the inspection of shale shaker screens produced by Derrick during the operation on Drill Rig at Dunga field/ Aktau (Maersk Oil project), preparation of the inspection report and test report - Provide service and support for installation and commissioning of oil and gas equipment in accordance with customer requirements. - Participation in tenders at tender.sk.kz and reestr.nadloc.kz - Preparing all necessary documentations for the tender.

Technical support for personal computers

Maintenance and repair of equipment of drilling rigs - Participate in scheduled preventative repair works (SPR) - Participate in the work on the descent casing and wellhead equipment, assembly and disassembly of equipment rigs. - Identify the causes of premature wear of equipment, adopts measures to prevent and eliminate - Daily reports on visual control - Repair of plunger pumps F-1800/1500, replacement of bearings, piston-rod, bushing and other parts.