Inspecting Electrical/instrumentation equipment for its compliance with the area classification (hazardous area drawing). As per ice-EX –Standards. Verifying-layout drawings, single line drawing, termination drawing for its correctness. Conducting- derailed, close& visual-grade of inspections as per requirement. Recording-all-faults and rectification details in the checklist as per IEC-EX-Standard. Preparation of Ex-register & collecting necessary details for it from field equipment. Rectification of faults food during an inspection, according to IEC-EX-Standards. UP dating, the faults found during an inspection according to its cause & effect. Categorizing the faults found during an inspection according to its cause & effect. De-certifying of instruments found with UN-Authorized modification/non-compliance-with-hazardous area classification as per IEC-EX-Standards. Inspecting Electrical/instrumentation equipment for its compliance with the area classification (hazardous area drawing). As per IEC-EX –Standards. Installing and maintaining electrical systems and equipment; Operating and maintaining electric motors, transformers, generators, controls, and other electrical equipment; Reading and interpreting blueprints, schematics, and electrical documents; Examining and diagnosing electrical systems and equipment.

Acceptance and commissioning of construction, installation and commissioning works on electrical equipment and instrumentation, telecommunication, FIre & Gas systems, compliance with PUE and KPO standards. Inspection of installation and testing of fiber-optic cables, power, signal cables, correctness of termination according to project drawings, KPO standards and specifications. Verification of correct installation of equipment earthing, earthing devices and lightning protection. Attendance and supervision during idle testing of instrumentation, fire and gas detectors. Correctness of connection and presence at testing of impulse, pneumatic lines according to specification and diagrams of piping and instrumentation. Verification of installation and testing of heaters (heat tracing) of pipelines. Control over the correctness of compliance with the project drawings and executive documentation on changes(RLMU), execution of project documentation. Making changes to the project documentation (Red-line), checking ITRs in the disciplines of electrical, instrumentation and telecommunication equipment.

Pre-inspection - Preparation and correction of all detected faults (installation and replacement of trusses, pressing cables, unplugging, installation of a doll (thermal shrinkage in the places of cable cutting). - About the cable ringing - Megger cable test - Outer Sheath Test cable 10kV - Cable installation in compliance with all requirements and regulations - Verification of cable tray installation according to diagrams - Verification of correct cable installation according to cable pathway diagrams - Checking correctness of cable connection as per diagrams - Checking of correctness of cable glands mounting as per manufacturer's instruction and IEC requirements - Collection and development of work package (collection of drawings, marking of required equipment on the drawings) - Preparation and opening of the application for inspection (NFI) - Preparation and completion of inspection sheets (QVD) - Conducting inspections to turn in volumes - Collect signatures of all inspection participants. - Supervise all aspects of quality control related to specialty during the construction phase to ensure compliance with company specifications and applicable codes. Inbound inspection of equipment, materials, and control of storage conditions. - Monitor electrical and instrumentation equipment, above and below ground, junction boxes, cable tray installation, cable pulling, cable stripping, sealing, marking, terminations, pipe bending and gauging. Liaising directly with customer's supervisory representative. Developing and preparing a list of questions to be answered during the inspection. Performing continuous monitoring of work being performed throughout the construction process. Reviewing field test reports. - Analyze and make independent recommendations for solutions to problems of varying complexity in accordance with organizational and/or project goals and guidelines. Review and sign executive and other documentation of electrical and instrumentation equipment. Performing inspections and testing of equipment and all types and types of cables according to the customer's executive documentation. Development of checklists, construction and quality inspection registers ; handling of variance requests and variance reports; Preparing and reviewing field test reports; reviewing and implementing calibration, test records for inspection equipment at construction site; conducting inspection and testing according to approved electrical and instrumentation drawings, procedures and standards; Inspection and verification of work in accordance with project procedures; appointment of inspections, i.e. making and sending NFI (notice for inspection); preparation of check lists (QVD) and certificates for signature, in accordance with ITP (inspection and testing plan); making reports on completed electrical installation work. Inspection and testing of 35, 110 kV high voltage cables Supervision of works, quality check of electrical installation works in accordance with the requirements of design documentation Prepare working documentation according to TCO standards Coordinate and approve working documentation with the customer Verification of compliance certificates

- Inspection of TCO construction sites on Electricity, installation of electrical installations (distribution boards, cables, glands). - management of technical documentation for construction of high-voltage lines of 110 and 35 kV. - Test results against standards tests of electrical equipment. - Testing of Electrical cables according to the project specification and standards. - Preparation of the required Quality Control (QC) Receipt and Transfer Documentation (QC). (Protocols, Certificates, Checklists) Preparation of executive drawings marked in red lines at the stage of construction and commissioning according to the requirements of the project, work with project documentation (single line circuits, cable circuits, equipment layout diagrams, cable logs). - ITP – (Inspection and test plan). - upload all drawings to the customer's POL / MCPlus / CoreWorx and CMS systems and their timely update. - Adjustment, correction of project documentation, drawings, electrical circuits. - Delivery of documentation package. - Installation and connection of HV Distribution boards, Earthing and cable trays. - Check for correct splitting, ringing of power cables. - Measurements of earthing resistance and isolation resistance of newly installed equipment. - Check of the resistance of the earthing circuit.

Tracing, diagnosing, and rectifying electrical faults. Using test equipment and hand tools to diagnose locate and fix electrical problems. Checking and testing electrical equipment and replacing them where required. Carrying out electrical installation and maintenance work Connection of wiring of electrical equipment. Working on different areas including in hazardous area (red zone) Working with different cable SWA cables. Interpreting work instruction, drawings, schematic diagrams. Investigation and troubleshooting, testing of electrical equipment, see below: Lighting system (normal, emergency and escape system) LV/HV motor system. UPS system. Earthing system. Circuit breaker and other components. Parts of ruck in/ruck out. Inspecting electrical components to ensure that high-quality work, see below: Inspection of the lighting system (6Month,1Year) as per RoK and local standards Inspection of LV/HV motor Inspection of Earthing system Inspection of HT/EL distribution board Inspection of the UPS system, electrical batteries. Administrative work like preparation of PTW for all type of electrical activities( Permit to Work, risk assessment, method statement), Audit. SAP (checking weekly activities, notification where required (Work Order), confirmation when work is done, (Fully, partially). Daily report for Line Manager. Preparation required material and tools for working. Took the highest level of care for keeping the workplace area safe, organizing by RoK and Company rules.